Maktec MT362 User Manual Page 1

Model No. DescriptionCONCEPT AND MAIN APPLICATIONS SpecificationDimensions: mm (")Width (W)Height (H)Length (L)362 (14-1/4)71 (2-13/16)194 (7-5/8

DISASSEMBLING[3] DISASSEMBLY/ASSEMBLY[3]-5. Impact BoltFig. 12(7) Remove O Ring case and Impact bolt from Tool holder complete. (Fig. 12)1. Insert (+

ASSEMBLING[3] DISASSEMBLY/ASSEMBLY[3]-5. Impact BoltFig. 14(2) Fix the Impact bolt section by fitting Ring spring 28 in the groove of Tool holder. (F

DISASSEMBLING[3] DISASSEMBLY/ASSEMBLY[3]-6. Swash Bearing 10Fig. 15(7) Disassemble Swash bearing section by removing Spur gear 10. (Fig. 16)(1) Disas

DISASSEMBLING[3] DISASSEMBLY/ASSEMBLY[3]-6. Swash Bearing 10Fig. 17Fig. 18(1) Assemble Swash bearing section as illustrated in Fig. 18.1. Install Ball

[3] DISASSEMBLY/ASSEMBLY[3]-7. Joining Swash Bearing section to Piston CylinderFig. 19CorrectWrongASSEMBLING1. Insert Guide plate to Piston cylind

[3] DISASSEMBLY/ASSEMBLY[3]-8. Assembling Inner housing to Gear housingASSEMBLINGPut Ball bearing 606ZZ in the Gear housing (Fig. 17),and assemble Inn

[3] DISASSEMBLY/ASSEMBLY[3]-9. Gear HousingFig. 24Assemble Oil seal 25, Flat washer 33, Ball bearing 6806DDW and Cup sleeve to Gear housing. (Fig. 24)

Repair1. It is recommended to replace the listed parts below when replacing carbon brush as a maintenance for longer service life of the machine.

MT870WhiteBlueBrownColor index of lead wires' sheathBlack* Noise suppressor* Noise suppressor is not used for some countries.Cord clampSwitchFo

Wiring diagramP 19/ 19Noise suppressorWiring in Motor HousingWiring of Noise SuppressorSwitchFix Lead wire(black) of Brushholder into thislead wire

Repair[1] NECESSARY REPAIRING TOOLSCAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.Code No. Description

[2] LUBRICATIONFig. 1AItem No.Item No.Description Grease AmountPortion to lubricatePortion to lubricateO ring 17.5Spur gear 51 Teeth portion for smoot

Fig. 2DISASSEMBLING1. Lever up Cap 35 with a slotted screwdriver and remove it by Hand, while holding Chuck cover with the other hand. Rem

Fig. 4DISASSEMBLING1. Lever up Change lever cover with a Slotted screwdriver by inserting it into a slot on Gear housing and do the same for an

DISASSEMBLING[3] DISASSEMBLY/ASSEMBLY[3]-3. Armature(1) Remove Handle cover and Carbon brushes to prevent Armature’s commutator from scratching. (Fig

[3] -4. Torque Limiter SectionDISASSEMBLINGDISASSEMBLINGASSEMBLING(3) Pull out Armature from Gear housing and remove Ball bearings and Washers. (Fig.

DISASSEMBLINGASSEMBLING(5) Disassemble Torque limiter section. (Fig. 10)Take the reverse steps of Disassembling. (Fig. 10)[3] DISASSEMBLY/ASSEMBLY[3]

DISASSEMBLING[3] DISASSEMBLY/ASSEMBLY[3]-5. Impact BoltFig. 11(1) Disassemble Tool holder section. (Fig. 2)(2) Remove Change lever. (Fig. 4)(3) Sepa